Computer-aided design of small patch antenna using (Al, Mg)TaO2 ceramics

Sung Hun Sim, Chong Yun Kang, Ji Won Choi, Seok Jin Yoon, Hyun Jai Kim, Young Joong Yoon

Research output: Contribution to journalArticle

2 Citations (Scopus)

Abstract

The microwave dielectric properties of (1 - x)(Al1/2Ta1/2)O2 - x(Mg1/3Ta2/3)O2 (AMT) (0 ≤ x ≤ 1.0) ceramics and the design of small coplanar waveguide fed antenna (CPWFA) have been investigated. (Al1/2Ta1/2)O2 and (Mg1/3Ta2/3)O2 have orthorhombic and tetragonal structure, respectively. As (Mg1/3Ta2/3)O2 concentration increased, AMT ceramics transformed into the tetragonal structure. Specimens having tetragonal single phase could be obtained above x=0.6. As (Mg1/3Ta2/3)O2 concentration increased, the grain size, dielectric constant (εr) and quality factor (Q) significantly increased and the temperature coefficient of resonant frequency (τf) changed from negative to positive. The τf of 0 ppm°C-1 was realized at x=0.65 and the Q · fo value and εr for this composition were 112470 GHz and 26.1, respectively. Newly developed 0.35(Al1/2Ta1/2)O2 - 0.65(Mg1/3Ta2/3)O2 dielectric materials were used for 1.5 GHz band CPWFA design and fabrication. The size of the CPWFA can be reduced by using high dielectric constant AMT ceramics, insetting slits into the patch, and fabricating CPW feed line in the ground plane. The slits play a role in not only lowering a center frequency but also fine tuning for the proposed antenna together with the open stub of CPW feed line. The CPWFA with slits has a lower center frequency than the conventional CPWFA, which suggests that the antenna size can be reduced by as much as 16.3%. The structure simulations of the CPWFAs have been performed to obtain impedance matching and to investigate the effects of slits. Experimental results of the fabricated device were in good agreement with the Simulation.

Original languageEnglish
Pages (from-to)207-211
Number of pages5
JournalJournal of Materials Science: Materials in Electronics
Volume13
Issue number4
DOIs
Publication statusPublished - 2002 Apr 1

Fingerprint

patch antennas
antenna feeds
computer aided design
Microstrip antennas
Antenna feeders
Computer aided design
Coplanar waveguides
slits
ceramics
Antennas
waveguides
antennas
permittivity
antenna design
impedance matching
Permittivity
resonant frequencies
dielectric properties
Q factors
Telephone lines

All Science Journal Classification (ASJC) codes

  • Electronic, Optical and Magnetic Materials
  • Atomic and Molecular Physics, and Optics
  • Condensed Matter Physics
  • Electrical and Electronic Engineering

Cite this

Sim, Sung Hun ; Kang, Chong Yun ; Choi, Ji Won ; Yoon, Seok Jin ; Kim, Hyun Jai ; Yoon, Young Joong. / Computer-aided design of small patch antenna using (Al, Mg)TaO2 ceramics. In: Journal of Materials Science: Materials in Electronics. 2002 ; Vol. 13, No. 4. pp. 207-211.
@article{a1394cb6d78d4871b6b6479e314af227,
title = "Computer-aided design of small patch antenna using (Al, Mg)TaO2 ceramics",
abstract = "The microwave dielectric properties of (1 - x)(Al1/2Ta1/2)O2 - x(Mg1/3Ta2/3)O2 (AMT) (0 ≤ x ≤ 1.0) ceramics and the design of small coplanar waveguide fed antenna (CPWFA) have been investigated. (Al1/2Ta1/2)O2 and (Mg1/3Ta2/3)O2 have orthorhombic and tetragonal structure, respectively. As (Mg1/3Ta2/3)O2 concentration increased, AMT ceramics transformed into the tetragonal structure. Specimens having tetragonal single phase could be obtained above x=0.6. As (Mg1/3Ta2/3)O2 concentration increased, the grain size, dielectric constant (εr) and quality factor (Q) significantly increased and the temperature coefficient of resonant frequency (τf) changed from negative to positive. The τf of 0 ppm°C-1 was realized at x=0.65 and the Q · fo value and εr for this composition were 112470 GHz and 26.1, respectively. Newly developed 0.35(Al1/2Ta1/2)O2 - 0.65(Mg1/3Ta2/3)O2 dielectric materials were used for 1.5 GHz band CPWFA design and fabrication. The size of the CPWFA can be reduced by using high dielectric constant AMT ceramics, insetting slits into the patch, and fabricating CPW feed line in the ground plane. The slits play a role in not only lowering a center frequency but also fine tuning for the proposed antenna together with the open stub of CPW feed line. The CPWFA with slits has a lower center frequency than the conventional CPWFA, which suggests that the antenna size can be reduced by as much as 16.3{\%}. The structure simulations of the CPWFAs have been performed to obtain impedance matching and to investigate the effects of slits. Experimental results of the fabricated device were in good agreement with the Simulation.",
author = "Sim, {Sung Hun} and Kang, {Chong Yun} and Choi, {Ji Won} and Yoon, {Seok Jin} and Kim, {Hyun Jai} and Yoon, {Young Joong}",
year = "2002",
month = "4",
day = "1",
doi = "10.1023/A:1014875816536",
language = "English",
volume = "13",
pages = "207--211",
journal = "Journal of Materials Science: Materials in Electronics",
issn = "0957-4522",
publisher = "Springer New York",
number = "4",

}

Computer-aided design of small patch antenna using (Al, Mg)TaO2 ceramics. / Sim, Sung Hun; Kang, Chong Yun; Choi, Ji Won; Yoon, Seok Jin; Kim, Hyun Jai; Yoon, Young Joong.

In: Journal of Materials Science: Materials in Electronics, Vol. 13, No. 4, 01.04.2002, p. 207-211.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Computer-aided design of small patch antenna using (Al, Mg)TaO2 ceramics

AU - Sim, Sung Hun

AU - Kang, Chong Yun

AU - Choi, Ji Won

AU - Yoon, Seok Jin

AU - Kim, Hyun Jai

AU - Yoon, Young Joong

PY - 2002/4/1

Y1 - 2002/4/1

N2 - The microwave dielectric properties of (1 - x)(Al1/2Ta1/2)O2 - x(Mg1/3Ta2/3)O2 (AMT) (0 ≤ x ≤ 1.0) ceramics and the design of small coplanar waveguide fed antenna (CPWFA) have been investigated. (Al1/2Ta1/2)O2 and (Mg1/3Ta2/3)O2 have orthorhombic and tetragonal structure, respectively. As (Mg1/3Ta2/3)O2 concentration increased, AMT ceramics transformed into the tetragonal structure. Specimens having tetragonal single phase could be obtained above x=0.6. As (Mg1/3Ta2/3)O2 concentration increased, the grain size, dielectric constant (εr) and quality factor (Q) significantly increased and the temperature coefficient of resonant frequency (τf) changed from negative to positive. The τf of 0 ppm°C-1 was realized at x=0.65 and the Q · fo value and εr for this composition were 112470 GHz and 26.1, respectively. Newly developed 0.35(Al1/2Ta1/2)O2 - 0.65(Mg1/3Ta2/3)O2 dielectric materials were used for 1.5 GHz band CPWFA design and fabrication. The size of the CPWFA can be reduced by using high dielectric constant AMT ceramics, insetting slits into the patch, and fabricating CPW feed line in the ground plane. The slits play a role in not only lowering a center frequency but also fine tuning for the proposed antenna together with the open stub of CPW feed line. The CPWFA with slits has a lower center frequency than the conventional CPWFA, which suggests that the antenna size can be reduced by as much as 16.3%. The structure simulations of the CPWFAs have been performed to obtain impedance matching and to investigate the effects of slits. Experimental results of the fabricated device were in good agreement with the Simulation.

AB - The microwave dielectric properties of (1 - x)(Al1/2Ta1/2)O2 - x(Mg1/3Ta2/3)O2 (AMT) (0 ≤ x ≤ 1.0) ceramics and the design of small coplanar waveguide fed antenna (CPWFA) have been investigated. (Al1/2Ta1/2)O2 and (Mg1/3Ta2/3)O2 have orthorhombic and tetragonal structure, respectively. As (Mg1/3Ta2/3)O2 concentration increased, AMT ceramics transformed into the tetragonal structure. Specimens having tetragonal single phase could be obtained above x=0.6. As (Mg1/3Ta2/3)O2 concentration increased, the grain size, dielectric constant (εr) and quality factor (Q) significantly increased and the temperature coefficient of resonant frequency (τf) changed from negative to positive. The τf of 0 ppm°C-1 was realized at x=0.65 and the Q · fo value and εr for this composition were 112470 GHz and 26.1, respectively. Newly developed 0.35(Al1/2Ta1/2)O2 - 0.65(Mg1/3Ta2/3)O2 dielectric materials were used for 1.5 GHz band CPWFA design and fabrication. The size of the CPWFA can be reduced by using high dielectric constant AMT ceramics, insetting slits into the patch, and fabricating CPW feed line in the ground plane. The slits play a role in not only lowering a center frequency but also fine tuning for the proposed antenna together with the open stub of CPW feed line. The CPWFA with slits has a lower center frequency than the conventional CPWFA, which suggests that the antenna size can be reduced by as much as 16.3%. The structure simulations of the CPWFAs have been performed to obtain impedance matching and to investigate the effects of slits. Experimental results of the fabricated device were in good agreement with the Simulation.

UR - http://www.scopus.com/inward/record.url?scp=0036539543&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=0036539543&partnerID=8YFLogxK

U2 - 10.1023/A:1014875816536

DO - 10.1023/A:1014875816536

M3 - Article

AN - SCOPUS:0036539543

VL - 13

SP - 207

EP - 211

JO - Journal of Materials Science: Materials in Electronics

JF - Journal of Materials Science: Materials in Electronics

SN - 0957-4522

IS - 4

ER -