Effect of array jet on cooling effectiveness on full-coverage film cooled surface

Dong Hyun Lee, Sang Hyun Oh, Eui Yeop Jung, Kyung Min Kim, Hyung Hee Cho

Research output: Chapter in Book/Report/Conference proceedingConference contribution

6 Citations (Scopus)

Abstract

In this study, the cooling effectiveness (φ) was measured on full-coverage film cooled surface with and without array jet impingement cooing using an infra-red thermographic technique. Measurements were conducted with two test plates of different thermal conductivities. One was made of stainless steel (k=16.3 W/m·K) and the other was made of polycarbonate (k=0.2 W/m·K). The measured cooling effectiveness comprises the adiabatic film cooling effectiveness on the film cooled surfaces, the heat conduction through the test plates and convective heat transfer of array jet impingement underneath the test plates. The inclination angles of film cooling holes and impingement jet holes were 35° and 90°, respectively. The diameters of both film cooling and impingement jet cooling holes were 5 mm. The streamwise and spanwise hole spacing-to-hole diameter ratios (p/d) are 3 for both the effusion plate (film cooled plate) and the injection plate (impingement nozzle plate. The holes on each plate were arranged in an inline pattern, while the film cooling holes and jet holes were positioned in a staggered manner. The jet Reynolds number based on the hole diameter was 3,000 and the equivalent blowing ratio (M) was 0.3. The gap distance between the jet plate and the film cooling plate was varied from 1 to 5 times of the hole diameter. In addition, the cooling effectiveness without impingement was tested, too. The stainless steel plate shows relatively higher and uniform cooling effectiveness than the polycarbonate plate. The effect of H/d was not significant for both test plates. However, the cooling effectiveness without the impingement jets decreases significantly for the stainless steel plate, while it changed a little for the cooling effectiveness of the polycarbonate plate.

Original languageEnglish
Title of host publicationProceedings of the ASME Summer Heat Transfer Conference 2009, HT2009
Pages565-572
Number of pages8
DOIs
Publication statusPublished - 2009 Dec 1
Event2009 ASME Summer Heat Transfer Conference, HT2009 - San Francisco, CA, United States
Duration: 2009 Jul 192009 Jul 23

Publication series

NameProceedings of the ASME Summer Heat Transfer Conference 2009, HT2009
Volume2

Other

Other2009 ASME Summer Heat Transfer Conference, HT2009
CountryUnited States
CitySan Francisco, CA
Period09/7/1909/7/23

Fingerprint

Cooling
polycarbonate
Stainless Steel
Polycarbonates
Stainless steel
Blow molding
Heat conduction
Nozzles
Thermal conductivity
Reynolds number
Heat transfer
Infrared radiation

All Science Journal Classification (ASJC) codes

  • Fluid Flow and Transfer Processes

Cite this

Lee, D. H., Oh, S. H., Jung, E. Y., Kim, K. M., & Cho, H. H. (2009). Effect of array jet on cooling effectiveness on full-coverage film cooled surface. In Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009 (pp. 565-572). (Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009; Vol. 2). https://doi.org/10.1115/HT2009-88420
Lee, Dong Hyun ; Oh, Sang Hyun ; Jung, Eui Yeop ; Kim, Kyung Min ; Cho, Hyung Hee. / Effect of array jet on cooling effectiveness on full-coverage film cooled surface. Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009. 2009. pp. 565-572 (Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009).
@inproceedings{d27ca7bcb9cc40bb9c167259d1aac6f9,
title = "Effect of array jet on cooling effectiveness on full-coverage film cooled surface",
abstract = "In this study, the cooling effectiveness (φ) was measured on full-coverage film cooled surface with and without array jet impingement cooing using an infra-red thermographic technique. Measurements were conducted with two test plates of different thermal conductivities. One was made of stainless steel (k=16.3 W/m·K) and the other was made of polycarbonate (k=0.2 W/m·K). The measured cooling effectiveness comprises the adiabatic film cooling effectiveness on the film cooled surfaces, the heat conduction through the test plates and convective heat transfer of array jet impingement underneath the test plates. The inclination angles of film cooling holes and impingement jet holes were 35° and 90°, respectively. The diameters of both film cooling and impingement jet cooling holes were 5 mm. The streamwise and spanwise hole spacing-to-hole diameter ratios (p/d) are 3 for both the effusion plate (film cooled plate) and the injection plate (impingement nozzle plate. The holes on each plate were arranged in an inline pattern, while the film cooling holes and jet holes were positioned in a staggered manner. The jet Reynolds number based on the hole diameter was 3,000 and the equivalent blowing ratio (M) was 0.3. The gap distance between the jet plate and the film cooling plate was varied from 1 to 5 times of the hole diameter. In addition, the cooling effectiveness without impingement was tested, too. The stainless steel plate shows relatively higher and uniform cooling effectiveness than the polycarbonate plate. The effect of H/d was not significant for both test plates. However, the cooling effectiveness without the impingement jets decreases significantly for the stainless steel plate, while it changed a little for the cooling effectiveness of the polycarbonate plate.",
author = "Lee, {Dong Hyun} and Oh, {Sang Hyun} and Jung, {Eui Yeop} and Kim, {Kyung Min} and Cho, {Hyung Hee}",
year = "2009",
month = "12",
day = "1",
doi = "10.1115/HT2009-88420",
language = "English",
isbn = "9780791843574",
series = "Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009",
pages = "565--572",
booktitle = "Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009",

}

Lee, DH, Oh, SH, Jung, EY, Kim, KM & Cho, HH 2009, Effect of array jet on cooling effectiveness on full-coverage film cooled surface. in Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009. Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009, vol. 2, pp. 565-572, 2009 ASME Summer Heat Transfer Conference, HT2009, San Francisco, CA, United States, 09/7/19. https://doi.org/10.1115/HT2009-88420

Effect of array jet on cooling effectiveness on full-coverage film cooled surface. / Lee, Dong Hyun; Oh, Sang Hyun; Jung, Eui Yeop; Kim, Kyung Min; Cho, Hyung Hee.

Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009. 2009. p. 565-572 (Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009; Vol. 2).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

TY - GEN

T1 - Effect of array jet on cooling effectiveness on full-coverage film cooled surface

AU - Lee, Dong Hyun

AU - Oh, Sang Hyun

AU - Jung, Eui Yeop

AU - Kim, Kyung Min

AU - Cho, Hyung Hee

PY - 2009/12/1

Y1 - 2009/12/1

N2 - In this study, the cooling effectiveness (φ) was measured on full-coverage film cooled surface with and without array jet impingement cooing using an infra-red thermographic technique. Measurements were conducted with two test plates of different thermal conductivities. One was made of stainless steel (k=16.3 W/m·K) and the other was made of polycarbonate (k=0.2 W/m·K). The measured cooling effectiveness comprises the adiabatic film cooling effectiveness on the film cooled surfaces, the heat conduction through the test plates and convective heat transfer of array jet impingement underneath the test plates. The inclination angles of film cooling holes and impingement jet holes were 35° and 90°, respectively. The diameters of both film cooling and impingement jet cooling holes were 5 mm. The streamwise and spanwise hole spacing-to-hole diameter ratios (p/d) are 3 for both the effusion plate (film cooled plate) and the injection plate (impingement nozzle plate. The holes on each plate were arranged in an inline pattern, while the film cooling holes and jet holes were positioned in a staggered manner. The jet Reynolds number based on the hole diameter was 3,000 and the equivalent blowing ratio (M) was 0.3. The gap distance between the jet plate and the film cooling plate was varied from 1 to 5 times of the hole diameter. In addition, the cooling effectiveness without impingement was tested, too. The stainless steel plate shows relatively higher and uniform cooling effectiveness than the polycarbonate plate. The effect of H/d was not significant for both test plates. However, the cooling effectiveness without the impingement jets decreases significantly for the stainless steel plate, while it changed a little for the cooling effectiveness of the polycarbonate plate.

AB - In this study, the cooling effectiveness (φ) was measured on full-coverage film cooled surface with and without array jet impingement cooing using an infra-red thermographic technique. Measurements were conducted with two test plates of different thermal conductivities. One was made of stainless steel (k=16.3 W/m·K) and the other was made of polycarbonate (k=0.2 W/m·K). The measured cooling effectiveness comprises the adiabatic film cooling effectiveness on the film cooled surfaces, the heat conduction through the test plates and convective heat transfer of array jet impingement underneath the test plates. The inclination angles of film cooling holes and impingement jet holes were 35° and 90°, respectively. The diameters of both film cooling and impingement jet cooling holes were 5 mm. The streamwise and spanwise hole spacing-to-hole diameter ratios (p/d) are 3 for both the effusion plate (film cooled plate) and the injection plate (impingement nozzle plate. The holes on each plate were arranged in an inline pattern, while the film cooling holes and jet holes were positioned in a staggered manner. The jet Reynolds number based on the hole diameter was 3,000 and the equivalent blowing ratio (M) was 0.3. The gap distance between the jet plate and the film cooling plate was varied from 1 to 5 times of the hole diameter. In addition, the cooling effectiveness without impingement was tested, too. The stainless steel plate shows relatively higher and uniform cooling effectiveness than the polycarbonate plate. The effect of H/d was not significant for both test plates. However, the cooling effectiveness without the impingement jets decreases significantly for the stainless steel plate, while it changed a little for the cooling effectiveness of the polycarbonate plate.

UR - http://www.scopus.com/inward/record.url?scp=77953011262&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=77953011262&partnerID=8YFLogxK

U2 - 10.1115/HT2009-88420

DO - 10.1115/HT2009-88420

M3 - Conference contribution

AN - SCOPUS:77953011262

SN - 9780791843574

T3 - Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009

SP - 565

EP - 572

BT - Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009

ER -

Lee DH, Oh SH, Jung EY, Kim KM, Cho HH. Effect of array jet on cooling effectiveness on full-coverage film cooled surface. In Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009. 2009. p. 565-572. (Proceedings of the ASME Summer Heat Transfer Conference 2009, HT2009). https://doi.org/10.1115/HT2009-88420