Focus pull-in behavior analysis in a blu-ray disk and various control approaches to enhance the performance of it

Kwang Hyun Lee, Hyunseok Yang, No Cheol Park, Young Pil Park

Research output: Contribution to journalConference article

Abstract

The focus pull-in behavior analysis in a Blu-Ray disk (BD) and various control approach to improve the performance of it are discussed. The focus pull-in work, which locks the beam spot of an optical pick-up to the information layer in an optical disk, is an essential work in an optical disk drive (ODD), and the error tolerance of it depends on the kind of an ODD. In a BD system, the focus pull-in work should be done within a very narrow beam height region (λ/NA = 0.4765 μm) and a very short period. Therefore, the moment of the focus pull-in is a transient phenomenon, and more careful analysis of it is necessary. In this paper, the focus full-in work is analyzed in depth, and various control approaches to improve the focus pull-in performance are discussed. First, various detected servo signal during the focus pull-in work are summarized briefly. Then, a novel swing arm type actuator which is developed by our center for a small form factor BD is introduced. Finally, three control approaches to perform the focus pull-in are designed and applied to the system: (i) conventional lead-lag, (ii) fuzzy control, (iii) sliding mode control. From the experiments results, we find that two control approaches, fuzzy control and sliding mode and, have more good focus pull-in performances than the conventional lead-lag approach.

Original languageEnglish
Article number604214
JournalProceedings of SPIE - The International Society for Optical Engineering
Volume6042 I
DOIs
Publication statusPublished - 2005 Dec 1
EventICMIT 2005: Control Systems and Robotics - Chongging, China
Duration: 2005 Sep 202005 Sep 23

Fingerprint

approach control
Half line
rays
optical disks
Fuzzy control
Fuzzy Control
Lead
sliding
Sliding mode control
Form Factors
time lag
Sliding Mode Control
Sliding Mode
Tolerance
Actuator
Actuators
Moment
Necessary
form factors
actuators

All Science Journal Classification (ASJC) codes

  • Electronic, Optical and Magnetic Materials
  • Condensed Matter Physics
  • Computer Science Applications
  • Applied Mathematics
  • Electrical and Electronic Engineering

Cite this

@article{6d1dc01a6f1b4bc692cc133545b49e81,
title = "Focus pull-in behavior analysis in a blu-ray disk and various control approaches to enhance the performance of it",
abstract = "The focus pull-in behavior analysis in a Blu-Ray disk (BD) and various control approach to improve the performance of it are discussed. The focus pull-in work, which locks the beam spot of an optical pick-up to the information layer in an optical disk, is an essential work in an optical disk drive (ODD), and the error tolerance of it depends on the kind of an ODD. In a BD system, the focus pull-in work should be done within a very narrow beam height region (λ/NA = 0.4765 μm) and a very short period. Therefore, the moment of the focus pull-in is a transient phenomenon, and more careful analysis of it is necessary. In this paper, the focus full-in work is analyzed in depth, and various control approaches to improve the focus pull-in performance are discussed. First, various detected servo signal during the focus pull-in work are summarized briefly. Then, a novel swing arm type actuator which is developed by our center for a small form factor BD is introduced. Finally, three control approaches to perform the focus pull-in are designed and applied to the system: (i) conventional lead-lag, (ii) fuzzy control, (iii) sliding mode control. From the experiments results, we find that two control approaches, fuzzy control and sliding mode and, have more good focus pull-in performances than the conventional lead-lag approach.",
author = "Lee, {Kwang Hyun} and Hyunseok Yang and Park, {No Cheol} and Park, {Young Pil}",
year = "2005",
month = "12",
day = "1",
doi = "10.1117/12.664589",
language = "English",
volume = "6042 I",
journal = "Proceedings of SPIE - The International Society for Optical Engineering",
issn = "0277-786X",
publisher = "SPIE",

}

TY - JOUR

T1 - Focus pull-in behavior analysis in a blu-ray disk and various control approaches to enhance the performance of it

AU - Lee, Kwang Hyun

AU - Yang, Hyunseok

AU - Park, No Cheol

AU - Park, Young Pil

PY - 2005/12/1

Y1 - 2005/12/1

N2 - The focus pull-in behavior analysis in a Blu-Ray disk (BD) and various control approach to improve the performance of it are discussed. The focus pull-in work, which locks the beam spot of an optical pick-up to the information layer in an optical disk, is an essential work in an optical disk drive (ODD), and the error tolerance of it depends on the kind of an ODD. In a BD system, the focus pull-in work should be done within a very narrow beam height region (λ/NA = 0.4765 μm) and a very short period. Therefore, the moment of the focus pull-in is a transient phenomenon, and more careful analysis of it is necessary. In this paper, the focus full-in work is analyzed in depth, and various control approaches to improve the focus pull-in performance are discussed. First, various detected servo signal during the focus pull-in work are summarized briefly. Then, a novel swing arm type actuator which is developed by our center for a small form factor BD is introduced. Finally, three control approaches to perform the focus pull-in are designed and applied to the system: (i) conventional lead-lag, (ii) fuzzy control, (iii) sliding mode control. From the experiments results, we find that two control approaches, fuzzy control and sliding mode and, have more good focus pull-in performances than the conventional lead-lag approach.

AB - The focus pull-in behavior analysis in a Blu-Ray disk (BD) and various control approach to improve the performance of it are discussed. The focus pull-in work, which locks the beam spot of an optical pick-up to the information layer in an optical disk, is an essential work in an optical disk drive (ODD), and the error tolerance of it depends on the kind of an ODD. In a BD system, the focus pull-in work should be done within a very narrow beam height region (λ/NA = 0.4765 μm) and a very short period. Therefore, the moment of the focus pull-in is a transient phenomenon, and more careful analysis of it is necessary. In this paper, the focus full-in work is analyzed in depth, and various control approaches to improve the focus pull-in performance are discussed. First, various detected servo signal during the focus pull-in work are summarized briefly. Then, a novel swing arm type actuator which is developed by our center for a small form factor BD is introduced. Finally, three control approaches to perform the focus pull-in are designed and applied to the system: (i) conventional lead-lag, (ii) fuzzy control, (iii) sliding mode control. From the experiments results, we find that two control approaches, fuzzy control and sliding mode and, have more good focus pull-in performances than the conventional lead-lag approach.

UR - http://www.scopus.com/inward/record.url?scp=33646508306&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=33646508306&partnerID=8YFLogxK

U2 - 10.1117/12.664589

DO - 10.1117/12.664589

M3 - Conference article

AN - SCOPUS:33646508306

VL - 6042 I

JO - Proceedings of SPIE - The International Society for Optical Engineering

JF - Proceedings of SPIE - The International Society for Optical Engineering

SN - 0277-786X

M1 - 604214

ER -