Grain refinement and mechanical properties of a metastable austenitic Fe-Cr-Ni-Mn alloy

Yunqing Ma, Jae Eun Jin, Young-Kook Lee

Research output: Contribution to journalConference article

12 Citations (Scopus)

Abstract

A lot of works for developing the structural nano-materials have been performed all over the world in recent years. Severe deformation techniques like HPT, ECPA and ARB have been applied to different materials such as Al, Cu, Ti and several steels. Such techniques greatly reduced the grain size and improved the yield and tensile strengths. However, the elongation of the materials is greatly decreased due to the small amount of work hardening, and these techniques do not seem suitable for the mass production. Therefore, this study has been carried out as a fundamental research for developing austenitic steels with high strength and good elongation using a conventional rolling and annealing processes. Fe-0.1%C-10%Cr-5%Ni-8%Mn alloy was melted, homogenized, hot rolled, and cold rolled at room temperature to transform γ austenite to a' martensite. After that, the specimens were annealed just above its reverse transformation finish temperature (Af) to obtain the fine reversed austenite grains. The grain size of the metastable austenitic steel was successfully refined to less than 200nm by repeating rolling and annealing processes. The resultant nanocrystalline material shows not only high strength but also large elongation because the work hardening ability is enhanced by the strain-induced martensitic transformation during the tensile test.

Original languageEnglish
Pages (from-to)43-48
Number of pages6
JournalMaterials Science Forum
Volume475-479
Issue numberI
Publication statusPublished - 2005 Apr 25
EventPRICM 5: The Fifth Pacific Rim International Conference on Advanced Materials and Processing - Beijing, China
Duration: 2004 Nov 22004 Nov 5

Fingerprint

Grain refinement
elongation
Elongation
work hardening
Austenitic steel
steels
mechanical properties
austenite
high strength
Strain hardening
Austenite
Mechanical properties
grain size
Annealing
Nanocrystalline materials
annealing
Steel
Martensitic transformations
martensitic transformation
yield strength

All Science Journal Classification (ASJC) codes

  • Materials Science(all)
  • Condensed Matter Physics
  • Mechanics of Materials
  • Mechanical Engineering

Cite this

@article{1004dc9c5b0b4dc882ca38ec444ee04b,
title = "Grain refinement and mechanical properties of a metastable austenitic Fe-Cr-Ni-Mn alloy",
abstract = "A lot of works for developing the structural nano-materials have been performed all over the world in recent years. Severe deformation techniques like HPT, ECPA and ARB have been applied to different materials such as Al, Cu, Ti and several steels. Such techniques greatly reduced the grain size and improved the yield and tensile strengths. However, the elongation of the materials is greatly decreased due to the small amount of work hardening, and these techniques do not seem suitable for the mass production. Therefore, this study has been carried out as a fundamental research for developing austenitic steels with high strength and good elongation using a conventional rolling and annealing processes. Fe-0.1{\%}C-10{\%}Cr-5{\%}Ni-8{\%}Mn alloy was melted, homogenized, hot rolled, and cold rolled at room temperature to transform γ austenite to a' martensite. After that, the specimens were annealed just above its reverse transformation finish temperature (Af) to obtain the fine reversed austenite grains. The grain size of the metastable austenitic steel was successfully refined to less than 200nm by repeating rolling and annealing processes. The resultant nanocrystalline material shows not only high strength but also large elongation because the work hardening ability is enhanced by the strain-induced martensitic transformation during the tensile test.",
author = "Yunqing Ma and Jin, {Jae Eun} and Young-Kook Lee",
year = "2005",
month = "4",
day = "25",
language = "English",
volume = "475-479",
pages = "43--48",
journal = "Materials Science Forum",
issn = "0255-5476",
publisher = "Trans Tech Publications",
number = "I",

}

Grain refinement and mechanical properties of a metastable austenitic Fe-Cr-Ni-Mn alloy. / Ma, Yunqing; Jin, Jae Eun; Lee, Young-Kook.

In: Materials Science Forum, Vol. 475-479, No. I, 25.04.2005, p. 43-48.

Research output: Contribution to journalConference article

TY - JOUR

T1 - Grain refinement and mechanical properties of a metastable austenitic Fe-Cr-Ni-Mn alloy

AU - Ma, Yunqing

AU - Jin, Jae Eun

AU - Lee, Young-Kook

PY - 2005/4/25

Y1 - 2005/4/25

N2 - A lot of works for developing the structural nano-materials have been performed all over the world in recent years. Severe deformation techniques like HPT, ECPA and ARB have been applied to different materials such as Al, Cu, Ti and several steels. Such techniques greatly reduced the grain size and improved the yield and tensile strengths. However, the elongation of the materials is greatly decreased due to the small amount of work hardening, and these techniques do not seem suitable for the mass production. Therefore, this study has been carried out as a fundamental research for developing austenitic steels with high strength and good elongation using a conventional rolling and annealing processes. Fe-0.1%C-10%Cr-5%Ni-8%Mn alloy was melted, homogenized, hot rolled, and cold rolled at room temperature to transform γ austenite to a' martensite. After that, the specimens were annealed just above its reverse transformation finish temperature (Af) to obtain the fine reversed austenite grains. The grain size of the metastable austenitic steel was successfully refined to less than 200nm by repeating rolling and annealing processes. The resultant nanocrystalline material shows not only high strength but also large elongation because the work hardening ability is enhanced by the strain-induced martensitic transformation during the tensile test.

AB - A lot of works for developing the structural nano-materials have been performed all over the world in recent years. Severe deformation techniques like HPT, ECPA and ARB have been applied to different materials such as Al, Cu, Ti and several steels. Such techniques greatly reduced the grain size and improved the yield and tensile strengths. However, the elongation of the materials is greatly decreased due to the small amount of work hardening, and these techniques do not seem suitable for the mass production. Therefore, this study has been carried out as a fundamental research for developing austenitic steels with high strength and good elongation using a conventional rolling and annealing processes. Fe-0.1%C-10%Cr-5%Ni-8%Mn alloy was melted, homogenized, hot rolled, and cold rolled at room temperature to transform γ austenite to a' martensite. After that, the specimens were annealed just above its reverse transformation finish temperature (Af) to obtain the fine reversed austenite grains. The grain size of the metastable austenitic steel was successfully refined to less than 200nm by repeating rolling and annealing processes. The resultant nanocrystalline material shows not only high strength but also large elongation because the work hardening ability is enhanced by the strain-induced martensitic transformation during the tensile test.

UR - http://www.scopus.com/inward/record.url?scp=17044373165&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=17044373165&partnerID=8YFLogxK

M3 - Conference article

AN - SCOPUS:17044373165

VL - 475-479

SP - 43

EP - 48

JO - Materials Science Forum

JF - Materials Science Forum

SN - 0255-5476

IS - I

ER -