Right sizes of nano- and microstructures for high-performance and rigid bulk thermoelectrics

Hongchao Wang, Je Hyeong Bahk, Chanyoung Kang, Junphil Hwang, Kangmin Kim, Jungwon Kim, Peter Burke, John E. Bowers, Arthur C. Gossard, Ali Shakouri, Woochul Kim

Research output: Contribution to journalArticle

83 Citations (Scopus)

Abstract

In this paper, we systematically investigate three different routes of synthesizing 2% Na-doped PbTe after melting the elements: (i) quenching followed by hot-pressing (QH), (ii ) annealing followed by hot-pressing, and (iii ) quenching and annealing followed by hot-pressing. We found that the thermoelectric figure of merit, zT, strongly depends on the synthesis condition and that its value can be enhanced to ∼2.0 at 773 K by optimizing the size distribution of the nanostructures in the material. Based on our theoretical analysis on both electron and thermal transport, this zT enhancement is attributed to the reduction of both the lattice and electronic thermal conductivities; the smallest sizes (2-6 nm) of nanostructures in the QH sample are responsible for effectively scattering the wide range of phonon wavelengths to minimize the lattice thermal conductivity to ∼0.5 W/m K. The reduced electronic thermal conductivity associated with the suppressed electrical conductivity by nanostructures also helped reduce the total thermal conductivity. In addition to the high zT of the QH sample, the mechanical hardness is higher than the other samples by a factor of around 2 due to the smaller grain sizes. Overall, this paper suggests a guideline on how to achieve high zT and mechanical strength of a thermoelectric material by controlling nano- and microstructures of the material.

Original languageEnglish
Pages (from-to)10949-10954
Number of pages6
JournalProceedings of the National Academy of Sciences of the United States of America
Volume111
Issue number30
DOIs
Publication statusPublished - 2014 Jan 1

Fingerprint

hot pressing
thermal conductivity
microstructure
quenching
annealing
thermoelectric materials
electronics
figure of merit
hardness
grain size
routes
melting
electrical resistivity
augmentation
synthesis
scattering
wavelengths
electrons

All Science Journal Classification (ASJC) codes

  • General

Cite this

Wang, Hongchao ; Bahk, Je Hyeong ; Kang, Chanyoung ; Hwang, Junphil ; Kim, Kangmin ; Kim, Jungwon ; Burke, Peter ; Bowers, John E. ; Gossard, Arthur C. ; Shakouri, Ali ; Kim, Woochul. / Right sizes of nano- and microstructures for high-performance and rigid bulk thermoelectrics. In: Proceedings of the National Academy of Sciences of the United States of America. 2014 ; Vol. 111, No. 30. pp. 10949-10954.
@article{d6cee52de0554d46b071a3caa9975642,
title = "Right sizes of nano- and microstructures for high-performance and rigid bulk thermoelectrics",
abstract = "In this paper, we systematically investigate three different routes of synthesizing 2{\%} Na-doped PbTe after melting the elements: (i) quenching followed by hot-pressing (QH), (ii ) annealing followed by hot-pressing, and (iii ) quenching and annealing followed by hot-pressing. We found that the thermoelectric figure of merit, zT, strongly depends on the synthesis condition and that its value can be enhanced to ∼2.0 at 773 K by optimizing the size distribution of the nanostructures in the material. Based on our theoretical analysis on both electron and thermal transport, this zT enhancement is attributed to the reduction of both the lattice and electronic thermal conductivities; the smallest sizes (2-6 nm) of nanostructures in the QH sample are responsible for effectively scattering the wide range of phonon wavelengths to minimize the lattice thermal conductivity to ∼0.5 W/m K. The reduced electronic thermal conductivity associated with the suppressed electrical conductivity by nanostructures also helped reduce the total thermal conductivity. In addition to the high zT of the QH sample, the mechanical hardness is higher than the other samples by a factor of around 2 due to the smaller grain sizes. Overall, this paper suggests a guideline on how to achieve high zT and mechanical strength of a thermoelectric material by controlling nano- and microstructures of the material.",
author = "Hongchao Wang and Bahk, {Je Hyeong} and Chanyoung Kang and Junphil Hwang and Kangmin Kim and Jungwon Kim and Peter Burke and Bowers, {John E.} and Gossard, {Arthur C.} and Ali Shakouri and Woochul Kim",
year = "2014",
month = "1",
day = "1",
doi = "10.1073/pnas.1403601111",
language = "English",
volume = "111",
pages = "10949--10954",
journal = "Proceedings of the National Academy of Sciences of the United States of America",
issn = "0027-8424",
number = "30",

}

Wang, H, Bahk, JH, Kang, C, Hwang, J, Kim, K, Kim, J, Burke, P, Bowers, JE, Gossard, AC, Shakouri, A & Kim, W 2014, 'Right sizes of nano- and microstructures for high-performance and rigid bulk thermoelectrics', Proceedings of the National Academy of Sciences of the United States of America, vol. 111, no. 30, pp. 10949-10954. https://doi.org/10.1073/pnas.1403601111

Right sizes of nano- and microstructures for high-performance and rigid bulk thermoelectrics. / Wang, Hongchao; Bahk, Je Hyeong; Kang, Chanyoung; Hwang, Junphil; Kim, Kangmin; Kim, Jungwon; Burke, Peter; Bowers, John E.; Gossard, Arthur C.; Shakouri, Ali; Kim, Woochul.

In: Proceedings of the National Academy of Sciences of the United States of America, Vol. 111, No. 30, 01.01.2014, p. 10949-10954.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Right sizes of nano- and microstructures for high-performance and rigid bulk thermoelectrics

AU - Wang, Hongchao

AU - Bahk, Je Hyeong

AU - Kang, Chanyoung

AU - Hwang, Junphil

AU - Kim, Kangmin

AU - Kim, Jungwon

AU - Burke, Peter

AU - Bowers, John E.

AU - Gossard, Arthur C.

AU - Shakouri, Ali

AU - Kim, Woochul

PY - 2014/1/1

Y1 - 2014/1/1

N2 - In this paper, we systematically investigate three different routes of synthesizing 2% Na-doped PbTe after melting the elements: (i) quenching followed by hot-pressing (QH), (ii ) annealing followed by hot-pressing, and (iii ) quenching and annealing followed by hot-pressing. We found that the thermoelectric figure of merit, zT, strongly depends on the synthesis condition and that its value can be enhanced to ∼2.0 at 773 K by optimizing the size distribution of the nanostructures in the material. Based on our theoretical analysis on both electron and thermal transport, this zT enhancement is attributed to the reduction of both the lattice and electronic thermal conductivities; the smallest sizes (2-6 nm) of nanostructures in the QH sample are responsible for effectively scattering the wide range of phonon wavelengths to minimize the lattice thermal conductivity to ∼0.5 W/m K. The reduced electronic thermal conductivity associated with the suppressed electrical conductivity by nanostructures also helped reduce the total thermal conductivity. In addition to the high zT of the QH sample, the mechanical hardness is higher than the other samples by a factor of around 2 due to the smaller grain sizes. Overall, this paper suggests a guideline on how to achieve high zT and mechanical strength of a thermoelectric material by controlling nano- and microstructures of the material.

AB - In this paper, we systematically investigate three different routes of synthesizing 2% Na-doped PbTe after melting the elements: (i) quenching followed by hot-pressing (QH), (ii ) annealing followed by hot-pressing, and (iii ) quenching and annealing followed by hot-pressing. We found that the thermoelectric figure of merit, zT, strongly depends on the synthesis condition and that its value can be enhanced to ∼2.0 at 773 K by optimizing the size distribution of the nanostructures in the material. Based on our theoretical analysis on both electron and thermal transport, this zT enhancement is attributed to the reduction of both the lattice and electronic thermal conductivities; the smallest sizes (2-6 nm) of nanostructures in the QH sample are responsible for effectively scattering the wide range of phonon wavelengths to minimize the lattice thermal conductivity to ∼0.5 W/m K. The reduced electronic thermal conductivity associated with the suppressed electrical conductivity by nanostructures also helped reduce the total thermal conductivity. In addition to the high zT of the QH sample, the mechanical hardness is higher than the other samples by a factor of around 2 due to the smaller grain sizes. Overall, this paper suggests a guideline on how to achieve high zT and mechanical strength of a thermoelectric material by controlling nano- and microstructures of the material.

UR - http://www.scopus.com/inward/record.url?scp=84904985327&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84904985327&partnerID=8YFLogxK

U2 - 10.1073/pnas.1403601111

DO - 10.1073/pnas.1403601111

M3 - Article

AN - SCOPUS:84904985327

VL - 111

SP - 10949

EP - 10954

JO - Proceedings of the National Academy of Sciences of the United States of America

JF - Proceedings of the National Academy of Sciences of the United States of America

SN - 0027-8424

IS - 30

ER -